29 heat neopixel 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
90 Degree Clip for NeoPixel Stick 8 mount to Ender 3 by azaranto
...to mount neopixel stick behind x-axis ponting light to heat ...
thingiverse
free
NeoPixel 8x / D4R-II Quadcopter Mount by hcker2000
...will allow you to also use zip ties plus heat shrink to hold the d4r-ii antennas in a v...
thingiverse
free
Neopixel Light Bar for 2020 extrusion
...ohm resistor)https://amzn.to/2s89xoo capacitor assortment (which has the 1000uf capacitor)https://amzn.to/3bioiki heat shrink tubing assortmenthttps://amzn.to/3bh1oyu ribbon cablehttps://amzn.to/3bknift crimping toolhttps://amzn.to/2vru3ia mainboard...
thingiverse
free
Neopixel HD Strip Mount for 3D printer by Chrome98
...this... the left side shows the status of the heat bed and the right - the extruder while they...
thingiverse
free
Voronoi Vase - Fits Gemma and 16 NeoPixel Ring by jolars
...my printrbot simple metal in translucent pla on a heatd bed. about 6 hours print time for...
thingiverse
free
FLIR Thermal Heat Map Light by adafruit
...mlx90614 temperature sensor to change the color of a neopixel ring to create heat map photography.this 3d printed project...
thingiverse
free
Raspberry Pi Camera Case w/ NeoPixel Ring (12 LED) by nixternal
...petg, or another transparent filament that can take high heat that neopixel ring can get hot! i would also...
thingiverse
free
Motion-Activated LED Wristband by adafruit
...project: • soldering iron • helping third hand • heat shrink pack • wire strippers • needles • 30...
thingiverse
free
Molex powered NodeMCU Neopixel Controller
...keep the overall height under 20mm) various diameters of heat shrink tubing 4 m3x16 allen head screws for the...
thingiverse
free
mophesto by maot1985
...is an installation description the bq support send me: http://www.mibqyyo.com/en-articles/2015/09/25/how-to-install-the-heated-on-your-prusa-i3-3d-printer/#/vanilla/discussion/embed/?vanilla_discussion_id=0 the voltage divider and the capacitive sensor for the...
thingiverse
free
The Division - Shoulder Beacon v3 by guido666
...rod into a "u" shape. you'll probably need to heat it with a torch, or it will break instead...
thingiverse
free
BLV NF Crazy and Orbiter 1.5 Extruder Mount with Hero Me Ducts by pfn0
...ducts (i used 4020 standard ducts) https://www.thingiverse.com/thing:4460970 extra bom: heat set inserts, i used 2 different kinds, unfortunately, you'll...
thingiverse
free
Neopixel MQTT Alarm Clock with Buzzer, RTC, Temperature, Humidity and Pressure sensor
...i used heat shrink and kapton tape. check for overheatng and good air circulation. the code for the wemos...
thingiverse
free
LED strip mount for Fluval Flex 37 by carpe_simian
...epoxy to seal them in (not sure about the heat from the leds though. for the silicone-sleeved leds, print...
thingiverse
free
The Division - Shoulder Beacon v2 by guido666
...rod into a "u" shape. you'll probably need to heat it with a torch, or it will break instead...
thingiverse
free
LJBot 0.5 Raspberry Pi Robot by jacksonliam
...3mm metal pin like i have. a bit of heat from a heat gun helps the metal pin fit...
thingiverse
free
Vase with hidden LED ring by fhogphil
...connectors back on, protect the joint with tape or heat shrink and plug them onto the nano and plug...
thingiverse
free
Space Goggles of Awesomeness by DrVegetable
...both battery leads at the same time! 0.) use heat shrink tubing to insulate all connections and switch terminals...
thingiverse
free
Adafruit NeoPixel Ring 12 Leds Fitting Cover by DKoss
...case 0://off for(int i=0;i<numpixels;i++){ pixels.setpixelcolor(i,0,0,0); } break; case 1: //heatng pixels.setpixelcolor(0,128,0,0); //pixel 0 is hot sample pixels.setpixelcolor(1,0,128,0); //pixel 1...
thingiverse
free
Deej Volume controller Case by KidCe
...box. what you need to build this: (optional) 4x heat insert m3 1x arduino nano 5x wh148 potentiometer 5x...
thingiverse
free
LED Matrix and Nodemcu stand by Stoney
...wires .. this matrix has a great deal of heat transfer ability (aluminium substrate maybe) and this killed the...
thingiverse
free
Glass Bed Lighting by DGDG5
...dupont diy kit heat shrink tubes cable clip ptc heatng plate (to solder the led's on the pcb) it's...
thingiverse
free
Chromalux Neopixel Lamp by BRUXXUS
...connect all the negative and positive wires together and heat shrink or tape them up. i hope you enjoy...
thingiverse
free
Doinker - 82mm Inductrix-style Brushless Quad by TheShortCrayon
...ws2812b addressable led pixel light 5050 rgb smd on heat sink pcb board 1-led led module pixels light 5v...
thingiverse
free
Holiday Light Necklace/Bulbs by CoasterLabs
...the bases black or dark green. paint, tape or heatshrink the wires to cover them up (you can use...
thingiverse
free
PiCade-HAT Based 10" HD Mini Bartop (Re-design) by Zurkeyon
...and down test once fully assembled. check components for heat close up the unit and make sure all controls...
thingiverse
free
Octoshield Case for Raspberry Pi 4 for Prusa Mk3 by adjuro
...the raspberry pi4 (must be done it is over heatng). have a raspberry pi cam plugged. have a webcam...
thingiverse
free
Pathfinder Head - Apex Legends by Xercium
...press the screw with the solder iron, it will heat up and sink into the model. i just used...
thingiverse
free
Octoprint Ultimate Lights / Fan / Temperature Control by vitormhenrique
...to vcc, 5v to jd-vcc and ground to gnd. heatr for heating my enclosure i got a $15 lasko...