19 fit slide makergear 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
MakerGear 2 drop_in_paxtruder_wedge by makerbotspace
...thingiverse this allows a makergear slide notch mount to fit in the drop in paxtruder. it is a small...
thingiverse
free
Yet another D-Link DSC Camera bracket for the Makergear M2 by CCVirginia
...dsc series of ip cameras with a bracket that fit on a makergear-m2. it may be placed in 2...
thingiverse
free
Bearing Spool Holder Remix, MakerGear M2 by SgtMunger
...cut about 20mm on the spindle fingers so it fit into my enclosure...
thingiverse
free
Supernatural Angel Blade by teejschmitz
...for each) and scaled them down a bit to fit on my makergear m2 (200 x 250 x 200...
thingiverse
free
MakerGear M2 Dial indicator mount by nirfriedman
...friction points with the rail. this allows for tight fit but at the same time the ability to slide...
thingiverse
free
Groove Mount #3 by koenkooi
...not even be required depending on how tightly it fit. . this derivative uses the other 2 bolt holes...
thingiverse
free
makergear m2 e3d filament drive and ez removable fan duct by Mrcleanr6
...detents. note: a couple people have mentioned the parts fit a little tight. please read the instructions. update 3/11/15...
thingiverse
free
Groove Mount #3 by tbuser
...not even be required depending on how tightly it fit. warning: i haven't actually attached it to a plastruder...
thingiverse
free
M2 80mm fan side mount by jsc
...m2 80mm fan side mount by jsc thingiverse press fit mount to attach an 80mm fan to a makergear...
thingiverse
free
Makergear M2 bearing spool holder by drandybuck
...friction as possible. so i designed a cylinder that fit standard skateboard bearings (22mm diameter), with a flange on...
thingiverse
free
Makergear X-Carriage with built-in fan mount and duct for cooling nozzle. by jeepsterjc
...fan mount clears the diagonals nicely and the bushings fit well, too. i should have a v5 with linear...
thingiverse
free
Part Cabinet - different drawer options by dellrio
...versions of the deep drawers, printed them, and they fit very well, the small gap from the previous version...
thingiverse
free
Makergear M2 Drawing Attachment (The Scribbler) by sthone
...a fine tip sharpie. (sanding might be required to fit the markers.) to use the markers i move (slide...
thingiverse
free
High Bypass Jet Engine Fan by Catiav5ftw
...colors! enjoy! if anybody has problems with parts not fiting, please comment and i can upload a revised file....
thingiverse
free
RAMPS 1.3 case by tJa
...printer mount. the corner plugs were too high to fit into the corner holes. the plugs for the arduino...
thingiverse
free
Bed camera mount for Makergear M2 by robertwallace
...bed's aluminum foot - it should be a snug fit replace the m3 screws. the existing ones should work....
thingiverse
free
Filament System Spool Holder For Robo 3d R1 +Plus by jdacal
...tight on purpose to allow for a nice snug fit on the bolt. so the wire brush will be...
thingiverse
free
Yet Another RepRap Style Printer by mblaster
...x end, but with the improvised design only one fit in. another big problem was the hex hole for...
grabcad
free
EZ-Jam
...e’, and a’ on the ez-jam in order to fit within the available space. to use the ez-jam, the...