21 end deckel 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Door Stopper by Asperli12
..."deckel" is simply clicked on the housing at the end the stopper(red) is made of tpu. you need to...
thingiverse
free
Filament Sensor (Tevo Tarantula) by bjoernras
...2mm thicker to prevent the screws from hitting the end of the...
thingiverse
free
Butter dish by DrDreid
...will be hard to put it together. at the end press the small "schlossdeckel" behind the locking mechanism and...
thingiverse
free
Öffner Deckel Kaffeekanne Bartscher by svendkramer
...in. the design is strenghtened, where it broke last time. i fear the new weak point is the pivot on the far end. let's see...
thingiverse
free
Schiebedeckel Box (Sliding Box) by Dr_Peacock
...aufzubewahren. die box hat einen schiebedeckel. dieser rastet am end und am anfang ein. so kann sich der deckel...
thingiverse
free
Schock Set / Schockbesteck
...many tries as the first player took. at the end of the round, the results are compared. the lowest...
thingiverse
free
Closable Ashtray by Dipling
...of the parts. i created an axle with an end head that connects the two lid components. this means...
thingiverse
free
Tiny Bubble Maker by ThinkingPegasis
...but my little experiment worked out and i will end it with...
thingiverse
free
Aceton smoothing ABS by cun
...a hissing sound stopped. then for 1-5 minutes , dependng on the desired result , wait. open the lid...
thingiverse
free
Jogurtbecher wiederverschliesser / Yogurt recloser by Eulach20
...my children never eat a yogurt cup at the end for this i have constructed a lid with which...
thingiverse
free
Big radial Fan by Dionarap
...rotation, otherwise the fan will not work at the end the pipe must be longer than the rotor, otherwise...
thingiverse
free
Raspberry Powerstation by Sjeppa
...push to switch off) 4 usb cable with open end cable m3x16 mm allen screw m3 nuts m6x16mm flat...
thingiverse
free
Löwen - Lion Lithophane extra gross by ronaldi40
...part top insert or adapter for e14 lamp lower end piece switch & power cord lion image in front...
thingiverse
free
think&have torque extruder by thinkandhave
...gear at a distance of 5mm from the opposite end of the part (non bearing end) an tap it...
thingiverse
free
Water Wheel Holders - Wasserrad - Halter by DorianGrey
...deckel bohren... ich habe mal aus solchen flaschen ein hängends beet mit mehreren solche halbflaschen übereinander gebaut. wenn ich...
thingiverse
free
Ikea Samla 22L - Drybox - Filamentbox - Trockenbox by Da_Neo
...thin washers between the double bearings and at the end 10x - small_washer.stl thick washers between bearing outer and...
thingiverse
free
Familien Sparclub, Spardose by Schneeking
...sachen gefallen würde ich mich sehr über eine kleine spend freuen. klickt auf den...
thingiverse
free
3$ 12v Dual LED Digit Temperature Controller Thermostat Housing (Relay Cycle Timing Delay) by SolarGermany
...löst (t1 timer) p1--2: zeitverzögerungsrelais nach t1 (t1-timer), dann endt die nachlaufzeit t2 nachfolgefreigabe (t2-zeit). p1--3: t1 verzögerungszeit relais...
thingiverse
free
Pop up sprinkler by Spotkiller
...the others and put a water tap at the end so you can evacuate your system. option 2: make...
thingiverse
free
Gearbox 256 / Getriebe 256 by CONSTRUCTeR
...video wird die kurbel mit etwa 10 u/min gedreht, während die angetriebene welle mit 2.560 u/min rotiert. zusammenfassend benötigt...
grabcad
free
Deckel SO flute grinder
...precise grinding of end mills flutes. up to 3/4" endmills can have the flutes re-ground with a full adjustment...