30 b bent 2 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
3dfindit
free
HSC-B Set 2 Short console steel connector bent
...hsc-b set 2 short console steel connector bent
3dfind.it
catalog: halfen
3dfindit
free
HSC-B Set 2 Long console steel connector bent
...hsc-b set 2 long console steel connector bent
3dfind.it
catalog: halfen
thingiverse
free
BenDoor stop by KFix
...version : 1mm / 1.5mm / 2mm b = pre-bent 3 versions : 1mm / 1.5mm / 2mm depending...
thingiverse
free
Replacement Elops B'twin led torch CL 500 by iRupert
...for elops bicycles from decathlon. the diode must be bent as in the picture, insert part 3 (it is...
thingiverse
free
Raspberry Pi 2 B+ mounting cage for Top Hat DIN Rail / Cap Rail / Hutschiene 35mm by Bash-T
...the notches of the cap rail mount. i carefully bent the clips a little bit before putting these two...
thingiverse
free
Cover for Raspberry Pi 3 by walter
...in one piece without support, and needs to be bent slightly to slide over the raspberry pi. atomic filament...
thingiverse
free
FrSky D8R-II Plus NO TUBE Antenna Holder Mount by Markacho
...one of the pictures that shows the antenna being bent this was made for the frsky d8r-ii plus, but...
thingiverse
free
Vectrex Joystick Housing Corner Braces by Fruktodlaren
...place very sneaky through the widened opening that the bent walls created. the joystick housing is just 0,5mm sheet...
thingiverse
free
Crank Mechanical System by Kazemoto
...motion, or vice versa. the arm may be a bent portion of the shaft, or a separate arm or...
thingiverse
free
Low Friction Feed for keeping filament dry by RetireeJay
...from dragging on the spool and creating friction, i bent some wire into a frame that supports the bag...
thingiverse
free
Muzzle Master (mask breather / glasses fog preventer), 3D print or laser cut by patricklingane
...that materials are ductile enough to not snap when bent in step 1 below. instructions for using it appear...
thingiverse
free
Quickswap carriage (narrow version for Anet A8/AM8) by bipsen
...not happy about the db connector (pins get easily bent in the db26hd connector), and i though it was...
thingiverse
free
TT Furious Tourbillon
...of the arduino, stepper, and rotary encoder wiring. i bent all the pins on the nano 90 degrees, to...
thingiverse
free
Wanhao i3: MKS Gen-L, Rasp Pi, Mosfet, TMC2130 Combo Adaptor and 120mm Cooling Mod by OmNomNomagon
...needs to be removed to allow the cable to bent enough to fit. this setup works perfectly with octopi,...
thingiverse
free
Model Rocket - B & C Engine Size by NEATman
...lighter weight motor retention system, made from a cleverly bent large paper clip to keep the weight down. to...
thingiverse
free
LED Diffuser for High Resolution 1701-D Warpcore by Novel_Mutations
...pixels that have been separated, wrapped in kapton tape, bent and push fit into the diffuser before being reconnected...
thingiverse
free
RC Jeep JK Chassis complete scale RC Car kit 1/10 by domi1974
...info from fourdogs that the rails have to be bent if you use version a. i added to new...
thingiverse
free
7 Segment LED Smart Clock by Surrbradl08
...2 leds each, then the ends have to be bent until the solder pads are exposed. it is recommended...
thingiverse
free
Eggfinder LCD Receiver Case by amiliv
...over all 5 pins, to reduce risk of accidentally bent pins shorting to each other or to the main...
thingiverse
free
Functional Pokéball - Nintendo Switch Game Cartridge Case by samk3ys
...springs for the button and hinge (cut it and bent the ends), though you may be able to find...
thingiverse
free
spotlights lampshade V2, GU10 or 12 V, glow in the dark, easyprint by Hedo
...i warmed up the butterfly on the wings and bent it a bit, this creates a 3d effect. you...
thingiverse
free
Spring Thunder - Shell Ejecting Foam Dart Blaster (WIP) by GDop26
...less which extends its life and resistance to being bent too far during jams. tapped rails: a response to...
grabcad
free
Hydraulic Pump
...-maximum rated flow 255 l/min (78 gal/min) -sae ports a,b rear end, 3/4" sae j518 -without loop flushing -standard...
cg_trader
$20
fully 3d printable RC aircraft - Cessna 152 | 3D
...the rear landing gear rod is made from a bent 2mm dia. stainless rod. hope you enjoy! please leave...
grabcad
free
DeWalt Battery to Ridgid Shop Vac Adapter
...from the backside. i flattened the nut’s teeth and bent it a bit to better fit the plastic’s curve....
grabcad
free
Vaccine Cooler for Cattle
...60ml syringe didier godefroy https://grabcad.com/library/plastipak-60ml-syringe beer cooler david merigian https://grabad.com/library/beer-cooler-1 ...
grabcad
free
Trailer Axle with Idler Hubs - 5 on 4-1/2 Bolt Pattern – 1300mm Long - 2,000 lbs / 900 Kg
...a bit higher and the sides of the axle bent lower allows the axle to give just enough to...
grabcad
free
Leitra velomobile redesign
...in the existing vehicle. ************************************************************************ the vehicle features a bent aluminum tube chassis, with four carbon leaf springs, and...
grabcad
free
Versatile Articulating Rotation-Stopper
...enhanced assy.stp (housekeeping: old stl files deleted and replaced b one step file of previous preliminary models as...
grabcad
free
Konecranes chain analyzer
...strain gauges; the top surface of the water can b determined. [if the crane was on an incline this...