17 angles land bracket 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Electrohub Landing Gear - Long by gsimpson2g
.... the bracket attaches to the side of the rail, with notches to help line it up and keep the landing gear level while tightening.
thingiverse
free
Electrohub Landing Gear - Short by gsimpson2g
.... the bracket attaches to the side of the rail, with notches to help line it up and keep the landing gear level while tightening.
thingiverse
free
Blade 230s Landing Gear by kingdallen
...ed to use thick ca glue and bob smith industries "insta-set" to glue the skids to the brackets for additional strength.
thingiverse
free
Landing Gear Bracket - RC Airplane by 7ofclubs
...as shown in the illustration above with 90 degree angles install a wheel with collars. i like to use...
thingiverse
free
RunCam Swift bracket for the Carbon Hornet 2B by liftbag
...to fly with strongly angled camera. the v7 allows angles from 20° to 60°, while the v6 goes from...
thingiverse
free
FT Storch Land Gear and Scoop. by mav68erick
...my plane atm.
scoop was made because i cut mine off, preping foam to build lol. printed scroop with supports so good side was up.
thingiverse
free
HSKRC Landing gear / skids by _gillies
...slit halfway through the coupling's length. use m2 screws (self tapping) in their respective holes to secure the leg members.
thingiverse
free
K4 Quad by goeland86
...arms to where the escs are have too sharp angles i'll need to redesign those completely for prototype v2....
thingiverse
free
Axel's modular 3D printed quadcopter (wooden arms) by Axbri
...plate, three different fpv camera mounting brackets with different angles and also mounts for frsky style pcb rx antennas....
thingiverse
free
Quadcake V1 - 3d printable acro quad frame 210mm by lazypc
...t enough clearance, i drilled new holes)
make battery bottom mounted with landing legs to make up height difference.
suggestions?
thingiverse
free
DJI Phantom 2 Carbon Fiber Skid (Rev 11/11/14) by jaln
...extra height skids. they also present a smaller aerodynamic profile these two factors should give you an increase in flight time.
thingiverse
free
DJI Phantom 2 Motor Mount Skid Carbon Fiber (obsolete 01/25/15) by jaln
...re some optional feet included (_skid_pad) they would probably be good for dirt, but these work fine on a hard flat landing pad.
thingiverse
free
Brunton Pocket Transit - Mount-Head Assembly & Staff Level V3 by Biketool
...ed.
additional information:https://en.wikipedia.org/wiki/survey_markerhttps://en.wikipedia.org/wiki/u.s._national_geodetic_survey
thingiverse
free
CONCEPTUAL DESIGN OF A HYBRID ELECTRIC DRONE AND COMPRESSED AIR by Isarts3d
...ooking good, until the drone designed to look like a huge bee. i liked the suggestion, then, from now on, this will be your name.
grabcad
free
GE Engine Bracket
...vide for lack of accuracy - if we can find a small enough round file.
our contact details will be provided to the lowest bidder.
grabcad
free
CADMAN CHALLENGE #4 - Autodesk Inventor Swing Bridge Series
...enge.com/
youtube playlist on cadman challenge channel:
https://www.youtube.com/playlist?list=pl_befedo5sh4l2rivl7mq9leja7bdeu8h
grabcad
free
NASA CHALLENGE - HANDRAIL CLAMP ASSEMBLY
...the rail at even shallower 25° (arrows c). the angles were more or less determined intuitively and proved satisfactory...