31 also v2 sag 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
cyclone fanduct v2 for HEVO MGN v2 by TFKKillermatrix
...the fanduct always sagged at higher bed temperatures. this also happened with the greentecpro carbon filament, which should have...
thingiverse
free
Hand Vacuum Wall Mount
...bit. i elongated the mount to improve stability. i also created a space above the mount for the power...
thingiverse
free
v2 Nintendo Switch 3-axis adjustable Joy-Con Grip - print in place by llakie
...hands by this adjustable 3-axis foldable grip. it can also be a test for the calibration of your printer....
thingiverse
free
Pop Pop Engine V3 by NatFaust
...i decided to add 1mm to its thickness. i also increased the volume because i believe it would add...
thingiverse
free
Smoke Detector Mount for Ender 3 by PinusTaeda
...tabs may not fit if you scale too large. also two of the tabs are unsupported, so you may...
thingiverse
free
Modular Battery Storage Holder Organizer by caesar_1111
...modular organizing solution for your common battery types. it also includes two size of generic boxes to cover for...
thingiverse
free
Ender 3/CR-10 Cable Guides by Kevlarr
...simply snaps onto the x endstop cover and i also included a second clip that mounts to a fang...
thingiverse
free
Anet E12 Fan V2 by M1dn1ghtN1nj4
...uses extra filament, but not enough to really matter. also added new support inside the nozzle so it doesn't...
thingiverse
free
Solidoodle Glass bed Magnet-mount with larger surface area. by Tomek
...i run my bed at, superglue dramatically weakens/softens/stops-being-awesome. it also doesn't like how i pop my prints in the...
thingiverse
free
Bowden guide Tronxy X5S by ozfunghi
...the files, made the rings a bit thicker, but also repositioned the ring on the extruder guide so that...
thingiverse
free
Closet Rod Spool Holder , No Sag and faster printing! by gamingoodz
...on this site and is much stronger. it will also fit spools that are up to 74mm wide so...
thingiverse
free
Ford Focus ST center console tray by chicken_lips
...focus rs console tray by majingrim here: https://www.thingiverse.com/thing:3769851 i also used the st logo text created by jackhydrazine here:...
thingiverse
free
Anet A8 cable strain relief by ozfunghi
...faster print (1h30m), less filament (13gr), more elegant, and also keeps the back springs tight and straight. push the...
thingiverse
free
Ender 5 Plus / CR-10S Pro/Max TFT43 Case by mikes2277
...those interested. other printers i am assuming it will also work on the cr-10s pro, ender 5 pro, cr-x...
thingiverse
free
Monoprice Ultimate 40mm blower fan duct by sgiacci
...after printing v6 i found the added cantilever was also binding the wires to the heater block. didn't know...
thingiverse
free
i3 Mega Fan Duct for V6 Hotend (No Cover) by OwenD30
...duct will sit perfectly flush with the cover. i also added a hole that goes around the bottom right...
thingiverse
free
Printrbot Simple X-axis Upgrade 296mmx227mm! by Roedkill
...printing large parts still has some issues. i am also using a heat bed pcb from makerfarm that is...
thingiverse
free
Sinden Lightgun Camera Protector by Hexxed
...it on my desk and not scratch the lens. also wanted something to be able to easily cover the...
thingiverse
free
Petsfang Bullseye Dual 4010 Duct by Derock25
...is the one that would fit in that scenario. also i have dual z motors on my ender 3.....
thingiverse
free
ENDER 5 PLUS / CR-10S PRO/MAX BTT TFT70 CASE by mikes2277
...and it just barely clears the bed's frame. it also hangs off the bottom. to be honest, it really...
thingiverse
free
Flsun linear rail X-Y gantry by jfunk
...chain to avoid sagging made the lj12a3 mount thinner also i was little underwhelmed at the quality when i...
thingiverse
free
CTC & Flashforge PLA Cooling Duct Fan Clips by Trezhunter
...the older designs with 40mm screws on the dual. also with creator pros i've heard scattered reports of a...
thingiverse
free
Extruder Fan Duct for Replicator 1 / Duplicator 4 / FlashForge by aplumb
...submitted a few final changes to v3 and i'm also publishing the cleaned up source sketchup file for you...
thingiverse
free
Screwless Cube Gears by emmett
...is practice for making a heart-gear version. this design also incorporates a couple of tricks that others may find...
thingiverse
free
Anet A8 AM8 Control board and FET Driver board enclosure by Jsschlat
...on the top and middle of the board. i also uploaded all the .stp files for the v3 case,...
thingiverse
free
Rostock Max V3/HE280 Slim Fan duct by Turpinator
...reduced weight and matl, as well as print time. also did a bridge test (http://www.thingiverse.com/thing:12925), except it didnt print...
thingiverse
free
Quick fit carriage system by lukie80
...all the wires takes some time. the wires have also to be placed carefully within the provided limited space....
thingiverse
free
Dyson Accessory Wall Bracket V7 V8 V10 V11 V15 Tool Holder for 6 or 8 Tools or Attachments by jarrah31
...break off after a couple of weeks use. i also wanted a version that didn't need supports. given how...
thingiverse
free
Hero Me Mutant HotEnd Cooling System by mediaman
...either heat press threaded inserts or m3 hex nuts. also note: photos included below were taken of an existing...
thingiverse
free
QIDI X-Max Dragon/V6 Hot End Remix by mrfumetsu
...duct - added another port for more coverage and also smoothed out the entire interior for better flow stiffen...
thingiverse
free
ReDuplicator i3 MK3x - Wanhao i3 Complete Aluminium Extrusion & Prusa Mk3 Overhaul by OmNomNomagon
...create an enclosure for the electronics. this project can also be built from scratch, or salvaged from other printers...