Adhesion fc 3d models
3dmdb logo

14 adhesion fc 3d models found

Download or buy, then render or print from the shops or marketplaces. 3D Models below are suitable not only for printing but also for any computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on your favorite 3d printer or render them with your preferred render engine. Please note that the 3D model database is only a Search Engine. You should visit the original websites. Most of the models can be easily imported and rendered with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online 3d model conversions tools for your file format.
thingiverse
free
(Matek) F405-wing FC board stand (and clones) by xxDvDxx

(Matek) F405-wing FC board stand (and clones) by xxDvDxx

...g wing. (affiliate links) fc (matek): https://bit.ly/39kt753 fc (clone): https://bit.ly/31kgt1l filament : https://bit.ly/3fjeglq
thingiverse
free
Naza M Flight Controller Carrier by tekcruzer

Naza M Flight Controller Carrier by tekcruzer

...even add a decrease risk of rf. 4) keep my fc in good condition should i need to trade it in/up. (no adhesive etc on the bottom).
thingiverse
free
Inductrix / Tiny Whoop frame by Jimbob

Inductrix / Tiny Whoop frame by Jimbob

...off the top of the ducts to help bed adhesion ...
thingiverse
free
Pixhawk 2.1 Cube Vibration Isolating Mount by lanceb

Pixhawk 2.1 Cube Vibration Isolating Mount by lanceb

...smaller footprint, and i'll post it when i do. i was going for lower profile on this. autodesk 123 & .stl files included
thingiverse
free
20x20 45 degree FC FPV Flight Controller adapter BetaFPV Twig by Mitri

20x20 45 degree FC FPV Flight Controller adapter BetaFPV Twig by Mitri

...good leveled bed and good printer i didn't use adhesion or a raft. i used 100% infill for most...
thingiverse
free
90mm copter frame addons for Tiny Whoop look by slibbinas

90mm copter frame addons for Tiny Whoop look by slibbinas

...also good) infill: 40% (or more) support: everywhere platform adhesion ...
thingiverse
free
Aston Villa Poker Card Capper by UWcharlie1983

Aston Villa Poker Card Capper by UWcharlie1983

...e isn't necessary, but i use a few drops to guarantee it never comes apart. enjoy and if you print one please post a picture!
thingiverse
free
Zeb'210 FPV Racer Quadcopter by ZeblodS

Zeb'210 FPV Racer Quadcopter by ZeblodS

...lub (french) remarks: solidworks files are included for customization. see my prototype in the made section for more information.
thingiverse
free
FT Goblin Parts by nesteffe

FT Goblin Parts by nesteffe

...the control horn mounts as you will get better adhesion with less risk of the paper delaminating from the...
thingiverse
free
MicroPrinted by akukan

MicroPrinted by akukan

...mw/200mw switchable aio 5.8g 72ch vtx 600tvl 1/3 cmos fpv camera rx : jeti duplex r5l ex ( shortened antennas ) tx : jeti dc-16
thingiverse
free
Relic FPV ImpulseRC Reverb Vtx + antenna bottom-plate mount by andrei_andros

Relic FPV ImpulseRC Reverb Vtx + antenna bottom-plate mount by andrei_andros

... sparse infill antenna tunnel is wider in middle to trap antenna nut, helping prevent fore/aft slippage flight- and crash-tested!
cg_trader
$3
Surfboard fin | 3D

Surfboard fin | 3D

...filaments, but make sure there is a proper layer adhesion ...
grabcad
free
3D printed Quadcopter V8

3D printed Quadcopter V8

...0.15 but use what's best for you. if layer adhesion is bad print a little hotter and use supports....
3dwarehouse
free
WOOD TRUSSES GA FILE NO. FC 5514

WOOD TRUSSES GA FILE NO. FC 5514

...ufacturer for information on the type of damper). *contact the manufacturer for more detailed information on proprietary products