21 8mm barbed 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
M20x1.5 male to 8mm ID barb by bummster
...e with my k40 didn't have the fitting i needed. this will fit a dymax 2000. i scavenged a 21mm od o-ring from somewhere else.
thingiverse
free
bulkhead barb by turboprint3D
...it is . 12mm threads 10mm large hose barb 8mm small hose...
thingiverse
free
Pass through barb fitting for flexible watercooling tube (ID 6mm x 8mm OD) by fujisama
..., i'm still learning. i hope the fcstd file is clean enough.
it's compatible with flexible silicone tube id 6mm x 8mm od.
thingiverse
free
Berlin Heart Model by zebra105s
...thingiverse it uses 3mm bolts for the barbs....sized for 8mm ...
thingiverse
free
5/16" or 8mm Water Pump Screen / Filter by TGit-Tech
...hingiverse
circular filter / screen for water pump with 5/16" ( 8mm - outer edge ) input barb. requires a hose connection.
thingiverse
free
Bulkhead Barb K40 Laser 8mmOD/5mmID by Slin_
...bulkhead barb k40 laser 8mmod/5mmid by slin_ thingiverse a barbed bulkhead for use with 8mm od 5mm id silicone...
thingiverse
free
irrigation 1/4 (8mm) tube end plug by Esq112358
...and tend to pop out. what created is a barbed end, much like the standard barbed end used with...
thingiverse
free
Wire Management for RepRap by PlanoRepRap
...the mendel rod then it snaps tight onto the 8mm or 5/16 rod. the wires are pushed inside and...
thingiverse
free
centrifugal pump compact reservoir by stoky996
...and the outer diameter of the barbs fit a 8mm hose be very careful when taking off the supports...
thingiverse
free
Pumpy the Younger by stmorgan
...should clamp around the 3/4 pipe and provide 4x 8mm mounting holes on a 50mm x 50mm square. should...
thingiverse
free
Barbed Hose Reducer / Hose Adaptor by Paul_Tibble
...1/16" 15mm 19/32" 1.75mm 1/16" 16mm 5/8" 1.75mm 1/16" 18mm 45/64" 2mm 5/64" 20mm 25/32" 2mm 5/64" 22mm 55/64"...
thingiverse
free
V85TT Valve Adjustment Tool by ScottTheFalcon
...normally use pliers on to be about 3mm x 8mm the "adjust" part pops into the "handle" for use....
thingiverse
free
Water flow switch by Klave
...it switches reliably. my magnets are thin discs, about 8mm x 1mm the round float piece is printed as...
thingiverse
free
DBS15 VGA breakout box by jamesambrose9
...4mm banana sockets you use, providing they have an 8mm mounting hole. i have a link the ones i...
thingiverse
free
RJ45, ethernet breakout box by jamesambrose9
...4mm banana sockets you use, providing they have an 8mm mounting hole. i have a link the ones i...
thingiverse
free
1/4" TRS Breakout box by jamesambrose9
...4mm bana sockets you use, providing they have an 8mm mounting hole. i have a link the ones i...
thingiverse
free
10 pin IDC breakout box by jamesambrose9
...4mm banana sockets you use, providing they have an 8mm mounting hole. i have a link the ones i...
thingiverse
free
4 pole Speakon socket breakout box by jamesambrose9
...4mm banana sockets you use, providing they have an 8mm mounting hole. i have a link the ones i...
thingiverse
free
DB9, RS232, Serial connector breakout box by jamesambrose9
...4mm banana sockets you use, providing they have an 8mm mounting hole. i have a link the ones i...
thingiverse
free
Ghostbusters Neutrino Wand Custom & Fixed Parts by WindDrake
...for the vent lens, which mates up with an 8mm led (ala. gbfans kit). at the request of my...
grabcad
free
TEC1-12706 and 40mm Cooling Block
...an attached liquid cooling block. barbs are designed for 8mm id tubing. block and peltier module are 40mm x...