15 1405 tensioner 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Simple 1405 Belt tension by VoltageMechanic
... on the plastic for locking the thread.
i may design a new one in the future but i haven't had any problems with this design.
thingiverse
free
Printrbot simple 1405 extruder spring tensioner by kbowen99
...akers kit extruder was too small and was unable to apply any tension to the filament. to fix the problem i printed a small spacer
thingiverse
free
Printrbot Simple 1405 Y-Axis GT2 Belt Tensioner Replacement Part by Saf
...elt could have been tensioned too tight, but i'm going to work on an alternate tensioner design, so keep checking my designs.
thingiverse
free
Belt tensioner for Printrbot Simple 1405 by mrAkuaku
...t broke in half.
before getting installing this, i was using a part i printed from here: http://www.thingiverse.com/thing:407389
thingiverse
free
Printrbot Simple 1405 Y-Axis GT2 Belt Tensioner Revised Design Part by Saf
... and the belt loop is tilted 5 degrees to try and keep the belt away from the printer.
m3 nut cutouts were added for ease of use.
thingiverse
free
Printrbot Simple 1405 Y-Axis GT2 Belt Tensioner Replacement Part Revision 2 by Saf
...n does not have a tilted or off-center belt loop.
everything should fit fairly snug, the openscad file is included for editing.
thingiverse
free
Printrbot Simple 1405 Y & X tensioner replacement by orangefurball
...roperly.
update 16 june 2014: x tensioner added, it is a bit longer than the original but should be ok. a wip until confirmation.
thingiverse
free
Beefier 208mm bed ends for 1405 Simple X Expanded (Single/Double Precision) by jhoff
...addition of a support ridge above the front rod tensioner ...
thingiverse
free
182mm X axis full print bed upgrade Printrbot simple 1405 makers edition 2015 by Makamaka
...added an x axis zero stop screw and belt tensioner to each side of the upgrade for ease of...
thingiverse
free
1405 300m No Sag Bearing Mod by danman1178
...es and it also actually reduces some of the belt vibration and allows for some belt tensioning as well depending on its rotation.
thingiverse
free
1405 Simple X ends - Remix by VoltageMechanic
...ngiverse.com/thing:275874).
design requires an additional four m3 nuts and four 20mm or longer screws to hold the parts together.
thingiverse
free
Printrbot Simple Adjustable YZ by iamjonlawrence
...the printrbot simple versions before the 1405. for the 1405 version please see:http://www.thingiverse.com/thing:723004 i have been running with this...
thingiverse
free
Belt Guide Printrbot Simple 1405 by averypierce
...) and if your screws are as bowed out from over tensioning as mine you'll probably need pliers and a hammer to force it down.
thingiverse
free
Printrbot simple 1405 GT2 belt bearing support by gerdescm
...ll, but i didn't try on that either because i had already hand fabricated a similar device since my printer was not operable.
thingiverse
free
1405 Simple X Expanded (Single/Double Precision) by iamjonlawrence
...ined those ideas into a 3d model. please review the conversation:http://www.printrbottalk.com/forum/viewtopic.php?f=21&t=6860