26 0.4x 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Orca 0.4x Toolholder by Okatake
...otrudes approximately 50mm from the body.
digitalmicrometer1
hexkey3
tweezers1
tweezers1
spanner1-3
nipper1
scraper1
screwdriver1
thingiverse
free
Orca 0.4x Y-belt clamp by Okatake
...orca 0.4x y-belt clamp by okatake
thingiverse
y axis belt clamp table
thingiverse
free
Orca V 0.4x feet by Chri
...orca v 0.4x feet by chri
thingiverse
just made some tiny feet for my buddy`s orca v0.40.
they should also fit v0.42.
thingiverse
free
Orca 0.4x Toolholder v2 by Okatake
...en with the spool holder beside body.
tool can be installed
hexkey3
tweezers1
tweezers1
spanner1-3
nipper2
scraper1
screwdriver*1
thingiverse
free
Orca 0.4x Filament Spool Guide by Okatake
...y okatake
thingiverse
i tried to make the spool guide base.
please use the "printrbot filament guide thingy" together.
thingiverse
free
Orca 0.4x Hotend cooling ring by Okatake
...ing for cooling the hot end.
※: possible distance to the bottom end of the hot (thermal core) is attached to the case of 47.5mm
thingiverse
free
Orca 0.4x GoPro Mount - With Filament Guide by Gyrobot
... orca stock filament guide with this to enable a gopro to be mounted.
http://www.gyrobot.co.ukhttp://www.facebook.com/gyrobotuk
thingiverse
free
Orca 0.4x(hotend v10) 608ZZ idler by Okatake
...e
thingiverse
was replaced with "608zz" the standard idler bearings.
with the offset, the feed filament may be smooth.
thingiverse
free
Orca 0.4x Direct Extruder(PG35L) by Okatake
...hingiverse
extruder with a direct drive gear for the orca v04x.
i have been using â€624zz" and "mk7 drive gear".
thingiverse
free
Orca 0.4x Dual Spool holder by Okatake
... to with two spool to fix the "http://www.thingiverse.com/thing:26523".
spool width : 76mm/59mm
spool inner diam : 52mm
thingiverse
free
Orca 0.4x parametric filament tube holder by GrimRepper
...rse
my orca 0.40 came without a spoolholder and filament guide. today i fixed this by adding a bit of ptfe tube and this holder.
thingiverse
free
Orca 0.4x spool holder for 1 Kg reels by www0
...drilling in the metal frame of your orca 0.4x, just replace the current spool holder with this one using the same bolts and nuts.
thingiverse
free
Orca 0.4x y-axis nut-trap. by Aggresive
... find it annoying having to line up nuts under the bed when replacing bearing holders etc, so i designed these to make it easier.
thingiverse
free
Orca 0.4x Dual Direct Extruder(PG35L) by Okatake
...quot;.
※:there is a need to change the control board ramps, etc. will not work in "generation 6 electronics" board.
thingiverse
free
Orca 0.4x Z Axis Adjuster by Macci
...can edit the iges files by your needs.
this project was inspired by mooselakes adjuster: http://www.thingiverse.com/thing:58897
thingiverse
free
E3d v6 hotend mount for Orca 0.4x by Aggresive
...top/bottom. this has not been tested, however, it should work ok. the filament hole is smaller, and is closer to the pinch-wheel.
thingiverse
free
Orca 0.4x RJMP LME8UU bearing housing by Aggresive
...he bearings to take up slack. just apply pressure to the housing (forcing the shaft to the edge of the bearing) while tightening.
thingiverse
free
Orca 0.4x 2x 624 bearing idler by Aggresive
...' of the bearings digging into the filament slightly.
(just realised the extruder is starting to look a bit christmas(y) :)
thingiverse
free
Orca 0.4x to Megatronics conversion. by Aggresive
...ight of the potentiometer and the two capacitors, shown in the picture.
update - have modified parts, hinge should now work. :)
thingiverse
free
Orca 0.4x Strut/Brace by Okatake
...of the frame. i have modified to respond to 0.4x ...
thingiverse
free
V10b Extruder Filament Guide 1,75mm by Okatake
...used in conjunction with "(hotend v10) 608zz idler orca 0.4xquot; ...
thingiverse
free
Orca 0.4x Holder for IGUS RJMP 01 08 slide bearings by dynai
...or a week and i love them.
happy more silent printing ;)
update: here's a video of them in action http://youtu.be/on6pa-qsfic
thingiverse
free
Telescopic Spool Holder by Gyrobot
...reels.this has been designed to replace the standard orca 0.4x spool holder, although could be mounted on any pair...
thingiverse
free
Gen 6 Deluxe PCB and Fan Enclosure by Gyrobot
...of the gen 6 deluxe pcb on my orca 0.4x but i guess this isn't a machine specific design....
thingiverse
free
Mountable Raspberry Pi Print Server by Gyrobot
...that has it's holes pitched to suit the orca 0.4x from mendel parts....
thingiverse
free
Iterated System Bamboo Shoots by TheHappyMew
...three transformations compared to the previous iteration are 0.35x, 0.4x and 0.45x from smallest to largest, though all z-axis...