26 terminals heatbed 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Terminals mount (heatbed) by rychuwit
..., i use terminals on the base . for the base i use epoxy glass laminat 2,5 mm .
terminals have many designs - for this scad file.
thingiverse
free
Prusa Lack Enclosure Heatbed Cable Clamp Nuts At Bottom - 60 Degree, for Screw Terminal Heatbed and Textile
...nd the nuts to the bottom. not as beautifully as uscbutterworth did, but it works.
updated with a picture of the installed clamp
thingiverse
free
BIQU Heatbed Power Module Mount by darkgrue
...op of the mean well se-450 mount.
this is primarily an open-air design; however, a clip is provided to shield the terminal block.
thingiverse
free
Prusa Mk2.5 Mk3 90 Deg Heatbed Cable Bracket for MK52 V2 Heatbed by Kerree12
...cable slack. you will need to bend the cable terminals with a pair of pliers so they are angled...
thingiverse
free
D6 WANHAO DUPLICATOR DUETWIFI & MKS V1.5 BOARD BRACKET & 120MM FAN POSTS by skuibreaker
...25mm above board to clear the heatbed & xs1 terminals ...
thingiverse
free
Heat Bed Wire Mount by chuteroo
...it in place 3). solder wires to the appropriate terminals on the heat bed 4). screw "heatbed clip bar"...
thingiverse
free
Angled MK3 Heatbed Cover with Nylon Filament Hole by zcubed
...for the original mk3 soldered bed terminals. the screw terminals on the newer beds will not...
thingiverse
free
MOSFET Mounting Bracket - Wanhao i3, Monoprice Maker Select V2 by uwe999
...iring info: http://3dprinterwiki.info/wiki/wanhao-duplicator-i3/di3-advanced-mods/heatbed-terminal-burning-fix-with-mosfet-board/
thingiverse
free
Universal Hotbed Mosfet Mount - Hotbed Burning Terminal Fix by HumbertoL
...guide, see: http://3dprinterwiki.info/wiki/wanhao-duplicator-i3/di3-advanced-mods/heatbed-terminal-burning-fix-with-mosfet-board/
thingiverse
free
Common Housing for Velleman K8200/3Drag Controller and Raspberry Pi with Camera by tr8
...t block m3 + spacer and 3 m3x16 screws with nut and washer)
the terminal block is optional (only for optional 24v heatbed supply)
thingiverse
free
Fabrikator mini aka Tinyboy Active Cooling Filament Fanduct by plasticmonk
...huge article on the fabricator mini with tips and tricks herehttp://3dk.berlin/de/content/30-fabrikator-mini-aka-tinyboy
(german)
thingiverse
free
Shorter MOSFET Mounting Bracket for Monoprice Maker Select V2, Cocoon Create, Wanhao i3 by patprints
...iring info: http://3dprinterwiki.info/wiki/wanhao-duplicator-i3/di3-advanced-mods/heatbed-terminal-burning-fix-with-mosfet-board/
thingiverse
free
Hotend and Heatbed PID Tuning - Gcode programs
...et heatbed temp to 0c
m117 hotend pid tuning done
g4 p4000
m117 by dareknorway https://www.thingiverse.com/thing:4226437
g4 p4000
thingiverse
free
Mosfet Holder for Anet A8 by Pawpawpaw85
...with the new anet a8 mainboard which has screw terminals moving the mosfets further away to avoid interference with...
thingiverse
free
Control Box by JKaechler
... the right side panel with connectors for steppers, thermistors, and heated parts, so i can disconnect it from printer if needed.
thingiverse
free
Adding MK3 heatbed to Vertex K8400 by Bo_Ris
...ing. relocated thermostat connector and added cover.
update 16-april-2018
uploaded corner and side things for 1mm thick heatbead.
thingiverse
free
Variable Power Supply Case (0-24V 20A) by ImyMe
...silicone insulation for good flexibility faston (7) and o-ring terminals (7-9) if you have crimping pliers or solder the...
thingiverse
free
ToyREP 3D Printer by thorgal
...have to be adjusted from power plugs to screw terminals also made minor changes in instructions and http://reprap.org/wiki/toyrep i've...
thingiverse
free
Shorter (Z Axis - 6mm) MOSFET Mounting Bracket for Monoprice Maker Select V2.1, Cocoon Create, Wanhao i3 by TallDonkey
...iring info: http://3dprinterwiki.info/wiki/wanhao-duplicator-i3/di3-advanced-mods/heatbed-terminal-burning-fix-with-mosfet-board/
thingiverse
free
Da vinci 1.0 MK3 alu heatbed upgrade by technomastermind
...st.
has explained in previous posts please turn on build plate pre-heat to prevent your printer firmware timing out on you.
enjoy
thingiverse
free
mophesto by maot1985
...d=0
the voltage divider and the capacitive sensor for the z-axis are from http://www.3d-proto.de/index.php?p=tips_autobed#autobed
thingiverse
free
MiniCube 3D Printer by Kotvic
...ring cable lug 50x ferrule (various size) for wire terminals 1m spiral wire wrap needed tools 1x sn-01bm crimp...
thingiverse
free
DE200 ULTIMODE BY RAGNA by ragnaroque
...a sertir, un assortiment de connecteur jst et de la gaine thermorétractables sont fortement recommandé également pour le montage.
thingiverse
free
Mortar Bot v.2 CoreXY 3D Printer by MortarArt
...one major cable hole, and holes for screw down terminals usb, wifi antenna etc. requires 12mm m3 stand offs,...
thingiverse
free
ReDuplicator i3 MK3x - E3D Hemera Mount with Bltouch and Filament Sensor
... sensor is available for testing via github, and will be published once properly tested. a pinda2 probe mount is also on the way.
thingiverse
free
Scalar Family - 3D Printer by 3DModularSystems
...model ssr25_cover 3.stl and rsdoc. the holes to access terminals have been removed as children can easily access these....