thingiverse

free

"Smartrap CoreXY"-like X Carriage with internal clamping belts (gets rid of the "in-the-way" belt clamping ears)") by florinf-ro

...at you can print it until you get a good result for belt grip. then you can print the whole carriage (which is not uploaded yet).

thingiverse

free

LBBR8-2LS SKF holder by qpidgiga

...thingiverse general purpose bearing holder for skf lbbr8-2ls (8mm internal 15 mm external, 24 mm lenght). designed for 3...

thingiverse

free

tronxy x5sa 3 wheel set-up by jonnijp

...support for the switch of y axis to fit internal ...

thingiverse

free

NERF Scout IX3 triggering mechanism by wiselynx

...ix3 triggering mechanism by wiselynx thingiverse replacement for the internal triggering mechanism of nerf blaster scout ix3. over time,...

thingiverse

free

Hot End Cable Support by RichardCS

...carriage. turn off support for the area where the internal hole for the cable tie hole is located.and print...

thingiverse

free

Rear Active Cooling Duct v3 for Qidi by CPTDangerCat

...boss removed, clearance added for the qidi lip, and internal material added for additional strength in the resulting corner....

thingiverse

free

Cable Chain Guard for Mostly Printed CNC / MultiTool by bhameline

...carriage of allted's mostly printed cnc / multitool. the internal length is 2.7" and the wall slots are made...

thingiverse

free

SSD Adapter for Lenovo TS130 Series by hemocyanin

...course, an ssd is much smaller than a 3.5" internal hd. so i printed up an adapter (in red)...

thingiverse

free

Adjustable Z-stop by jesc

...the x-carriage using the existing nut there, with an internal nut and screw assembly such that you can turn...

thingiverse

free

TEVO TARANTULA E3DV6 PART COOLING FAN DUCT by Albatrossity

...carriage and a e3dv6 hotend. duct has a small internal baffle to help the air circulate around the duct...

thingiverse

free

Dial indicator support for Tevo Tarantula by AntonioGPS

...use two 6mm screws that are tightened to two internal bolts that are introduced into the piece. to avoid...

thingiverse

free

E3D V6 mounts by Bogomi67

...tight, to get a good bond. the parts have internal structure for strenght, but i recommend 20% infill or...

thingiverse

free

009 short bogie carriage model railway

...light. it is hoped to electrify the carriage for internal lighting and a 3mm red led tail light. i...

thingiverse

free

3D Printer 4xLM8UU Minimal X Carriage (with symmetric/balanced tensioning mechanism) for F694zz bearings & more [#SCOUTcorexy design] by florinf-ro

...it. the advantage of increased rigidity due to the internal belt grippers is maintained. please ask questions if you...

thingiverse

free

Cheap Roller Carriage for DLT-180(Chinese Kossel 2020) by niisaka

...nyloc nut tamiya long screws release you from terrible internal nuts. traditional m3x25mm screws and nuts also work instead...

thingiverse

free

Rostock Mini - 3mm Bowden - Traxxas 5347 - 18 tooth GT2 pulley - pasqal version by pasqal

...6/3mm ptfe tube and change 6/4mm ptfe tube. 4mm internal diameter causes problems with tension of filament and...

thingiverse

free

Ender 6 - Befenybay 10x20 Mount - BMG Clone Direct Drive - Linear Rail by Dstrm

...mount x carriage" by tertullidanhttps://www.thingiverse.com/thing:4800961 designed for befenybay r18 internal size 10x20mm drag...

thingiverse

free

Original Prusa MINI E3D Standard Heater Block - X-Carriage R4 by Chrizz

...for them it's also really hard to do revisions internaly because its infested with 50+ features and a bunch...

thingiverse

free

Y Belt Attachment - Prusa i3 by daGHIZmo

...in this case i prefer to insert nuts in internal housing of the parts, to obtain a cleaner installation;...

thingiverse

free

Bi-fold door top slider - 4" long for 3/4" rail by mgx

...fits rails that are 18mm wide (3/4") and 12mm internal (1/2"). i've also included the original openscad source in...

thingiverse

free

The Diablo: A carriage solution for C/D/E-Bots using the Flex3Drive Dual by Manbehindthemadness

...bottom (drop 2 m3 hex nuts into the aft internal mounting holes within the flex drive). → i have...

thingiverse

free

D-Bot Titan radial blower fan (for 1sPiRe's carriage) by nmaggioni

...(taller holes might have blowed onto the nozzle). removed internal glitched structure obstructing airflow. updates 27/04/2018 - removed an...

thingiverse

free

HextrudORT - Carriage for HevORT STD/HD MGN12 config by MirageC

...lightweight print head for fast 3d printing. re-using the internal components from the popular and efficient bondtech bmg, this...

thingiverse

free

HextrudORT - Carriage for HevORT STD/HD MGN9 config by MirageC

...lightweight print head for fast 3d printing. re-using the internal components from the popular and efficient bondtech bmg, this...

thingiverse

free

Fully Printable Y carriage on 200x200 bed with bearing IGUS STYLE by ChuckNorris90

...0.4 nozzle and the size is perfect. *11/02/17 - internal part of the lm8uu (100mm) bearing edited so that...

thingiverse

free

Pen Holder for DIY Dremel CNC by goth2k

...). it might fit other dremel holders too. the internal diameter is 12mm, it should fit most pens and...

thingiverse

free

Ender 6 - Befenybay 10x20 Mount - Y Mount - Linear Rails - Cable Chain by Dstrm

...linear rail mod" by ernest93:https://www.thingiverse.com/thing:4757747 designed for befenybay r18 internal size 10x20mm drag chain:https://www.amazon.com/gp/product/b07sfft1k5 and made to align with...

thingiverse

free

XYZ Da Vinci 1.0 Three fan extruder carriage. by firecardenal

...air from the chamber and taking it through an internal duct in the carriage to the printing area. this...

thingiverse

free

HextrudORT - Blank Back Plate for DIY integration by MirageC

...lightweight print head for fast 3d printing. re-using the internal components from the popular and efficient bondtech bmg, this...

thingiverse

free

HextrudORT - Carriage - for HevORT HD12 configuration by MirageC

...lightweight print head for fast 3d printing. re-using the internal components from the popular and efficient bondtech bmg, this...

thingiverse

free

Filament Reel Roller for Prusa i3 Steel by MalcolmSharp50

...left hand and right hand frames and the two internal frames. countersunk m3 bolts are used to clamp the...

thingiverse

free

AnyCubic Kossel Linear Plus V-Rail mod plus corner cover by Narosenberg

...and any other trash off the motors and the internal of the printer. solidworks models are available for both...

thingiverse

free

Tevo Tarantula Cable Conduit by JunkYardDawg

...collection of various types of drag chain links with internal measurements of 12mm x 14mm for a very compact...

thingiverse

free

Redesigned Prusa i3 X carriage by julieng7

...isostatic assembly. it's recommended to insert the nut in internal housing of the part to obtain a cleaner installation...

thingiverse

free

Hypercube Evolution/ Hevo BMG direct extruder carriage by BerronGears

...it):https://www.thingiverse.com/thing:2254103 features: -david crocker's ir sensor mount -bl-touch mount -internal cable routing for fans part list: -4020 blower fan...

thingiverse

free

v-rail for v-slot based builds by Rafael_Rosa

...v-slot based mountings. it still needs support for the internal groove, as i wanted to keep compatibility with the...

thingiverse

free

Filament Feed Tube Holder by Wolfie

...holder out or edit the mesh to enlarge the internal diameter. i made sure the polys are clean so...

thingiverse

free

Bukoschnozzle Circular Fan Duct by buildrob

...(larger) version of the fan duct which has a internal diameter which is 4mm larger (37mm). this gives more...

thingiverse

free

RichRap's Quick-Fit X-Carriage for MendelMax 2.0 by JEZZMUND

...body for both style and strength. i've resized the internal geometry and cutout to make space for the new...

thingiverse

free

TinyCube by haxd

...v2 of z axis stepper motor fixture made the internal screw hole bigger so i can fit a standard...

thingiverse

free

Stock Ender 3/CR10 hotend mount/adaptor for CR10-V2/V3 by hairyfacedhooman

...carriage mounting points of the cr10-v2/v3, (and tweaked the internal somewhat) to allow you to use a standard creality...

thingiverse

free

YAZA - yet another Z switch adjuster (Ultimaker) by MoonCactus

...because of something that (tried to) slide against the internal plywood wall. the only parts here that are in...

thingiverse

free

3D Printer 3xLM8UU Minimal X Carriage (with symmetric/balanced tensioning mechanism) [#SCOUTcorexy design] by florinf-ro

...wip x carriage that implements, like its predecessor, an internal belt gripping system and adds to it in functionality...

thingiverse

free

Printed double IGUS Bearing block for E3D baseplate by bipsen

...carriage moves without binding. i had to set the internal diameter til 15.3mm in order to get the igus...

thingiverse

free

HextrudORT - Extruder for Nova End by MirageC

...lightweight print head for fast 3d printing. re-using the internal components from the popular and efficient bondtech bmg, this...

thingiverse

free

PrintRite DIY 3D Printer Fan Duct v3 by thedayowl

...adapter 40mm fan adapter 2nd lower duct option with internal supports for shorter bridging during printing flat 40mm fan...

thingiverse

free

OCD Prusa MK2/S X-Carriage Adjustable Tensioner. by CO-OCD

...believe 3. as you can see, the tensioner is internal to the original part so it fits exactly as...

thingiverse

free

Prusa i3 Y-axis carriage for 4 bearings by adruss85

...the holes for 2.5mm 2nd operation mill out the internal cutouts and bearing cutouts (6mm slot drill) 3rd operation...

thingiverse

free

HextrudORT - STDHT NOVA MGN9 - Embedded Extruder for HevORT 3D Printer by MirageC

...lightweight print head for fast 3d printing. re-using the internal components from the popular and efficient bondtech bmg, this...

thingiverse

free

HextrudORT - STDHT NOVA MGN12 - Embedded Extruder for HevORT 3D Printer by MirageC

...lightweight print head for fast 3d printing. re-using the internal components from the popular and efficient bondtech bmg, this...

thingiverse

free

HextrudORT - Extruder for Dragon Hotend by MirageC

...lightweight print head for fast 3d printing. re-using the internal components from the popular and efficient bondtech bmg, this...

thingiverse

free

Servo Mount - Automatic Blast Gate 4"/100mm by sennah91

...into the plastic. as my servo shaft has an internal thread, i additonally secured the small arm via the...

thingiverse

free

Flush mount 2X3 leg brace by sswilson

...edge of the table/cabinet or facing out from an internal pedestal. initially designed for mounting under a wooden virtual...

thingiverse

free

CAM LEVER ASSEMBLY (5/16-18 CARRIAGE BOLTS) by mkoic

...the other parts. this is similar in concept to https://www.amazon.com/kipp-04232-2011a3-levers-internalsurface/dp/b013i9ziom/ref=sr_1_24?dchild=1&keywords=cam+lever&qid=1599146844&sr=8-24 ...

thingiverse

free

Aux Blower Fan for MP Select Mini - REMIX by SLOPOS

...push air out of the structure because of the internal turbulence. i suggest printing fan side down with bed...

thingiverse

free

High Accuracy Dovetail Stepper Slide by 3DPRINTINGWORLD

...stepper motor and there is some play in its internal gearing. this remix resolves the issue by utilizing a...

thingiverse

free

Modular A for Anet A2 3D Printer by OverEngineeredByDefault

...but with all new features included as well. features: internal structures for applying more stiffness, embedded metal mounting nuts,...

thingiverse

free

Kossel / 2040 Mount Adapter for Bondtech's Standard Mount. by DAcreates

...see i'm using capricorn tube, this has a lower internal size but to stop it coming out i had...

thingiverse

free

Paste Extruder by simlrh

...own so cable doesn't clash with printer case adjust to take an xg z40 syringe adjust to use more standard 100mm m6 hex bolts?

thingiverse

free

E3D v6 Direct Drive Extruder by nplan

...m3 and m4 nuts and bolts a spring, minimal internal diameter: 4mm the extruder works extremly well with classic...

thingiverse

free

Sparkcube radial fan mount by PaddyCube

...30mm wide. sparkcube_radial_fan_duct_30mm is a ring cooler with an internal diameter of approx. 30mm sparkcube_radial_fan_duct_30mm_incr_gap has the same size...

thingiverse

free

Direct Drive Extruder Mount for MGN12H (Titan, BondTech, E3D V6) by Quadropus

...used staples to do that. the fan mount has internal cable routing aswell as the extruder mount. the cables...

thingiverse

free

Sidewinder X1 V4 Hemera Mount by Nyles

...straight away from the heater in order to minimize internal mangling of the connector. note that if you're using...

thingiverse

free

Geeetech mini rostock delta g2s pro linear bearing by gordonendersby

...little bigger or print with more clearance on the internal diameter. awkward and time consuming to test as im...

thingiverse

free

Remote Driven Extruder, not a bowden by blitz2190

...larger but remember the 608 only has a 8mm internal diamater so that would be the limit, the big...

thingiverse

free

SWX1 Linear Upgrade

...i used a clone bmg for use of the internal parts (bondtech gears, motor gear, hinge pin, etc (10)...

thingiverse

free

ET4 X Linear Rail by peddomgar

...a m3x18 screw to fix the nuts in the internal hex hole, then do the same for left part,...

thingiverse

free

Rigidbot Big Buildplate Counterweight by virtualight

...by virtualight thingiverse you wouldn't run a single piston internal combustion engine without a counterweight as it would shake...

thingiverse

free

E3D mount for MP Select Mini by aliimam

...i have a backup design to add manual supports internaly. fixed the e3d mount snuggness. moved the nozzle down...

thingiverse

free

GT2 belt clamp (Prusa Y-axis) by RGN01

...ution-noncommercial-sharealike 4.0 international license. see http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.

thingiverse

free

HeroYou CR-10S Pro

...cooling nozzle a bit, also removed some of the internal baffles that did nothing for air flow at the...

thingiverse

free

Filament guide for IKEA Lack Enclosure with Mosaic Palette 2s Pro by pinguinone

...following the x-carriage while it moves along the x-axis. internal dimensions allows use of the tube from the mosaic...

thingiverse

free

Anycubic 4Max Pro circular fan duct by Bemko

...air outlets and the screw mount. there are some internal support structures that allow to print this without any...

thingiverse

free

Blower Fan Duct for MTW Minimax by Beerglut

...it is needed without cooling the heater block. an internal vane helps equalise the air pressure on all sides...

thingiverse

free

Creality CR-6 BMG direct drive mount directly on the strain gauge by K2Van

...printing resulted in a working extruder. i salvaged the internal of my bmg clone and installed them in the...

thingiverse

free

Chimera Zesty Nimble X-carriage for Prusa i3 clone by RGN01

...ution-noncommercial-sharealike 4.0 international license. see http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.

thingiverse

free

Using a Cheap Tire Gauge as a Probe by JMadison

...screw heads are flush with the switch body.https://www.aliexpress.com/item/free-shipping-10pcs-2pin-n-o-n-c-5a250vac-limit-switch-wk11-3z-mini-micro-switch/32273563395.html the internal spring that keeps the probe extended is a 8.5...

thingiverse

free

Hypercube Evolution Upgrade All Parts by NedalLive

...+ bl touch https://www.thingiverse.com/thing:2366952 z carriage for lm12uu all internal dimensions are provided with 0.2 to 0.4 in addition...

thingiverse

free

Voron Afterburner Direct Drive Mount for CR-10/Ender 3/etc. by TroyJoachim

...with connector bmg extruderyou will need all of the internal parts from the bmg for the afterburneramazon linkaliexpress link...

thingiverse

free

E3D Chimera / Cyclops mount for Prusa i3 X-Axis carriage upgrade by RGN01

...ution-noncommercial-sharealike 4.0 international license. see http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.

thingiverse

free

narrow gauge passenger car (and roof) for use with AJAX NN3 loco

...job to remove the supports, not to mention the internal area with supports inside!, so sorry to anyone who...

thingiverse

free

Maker farm i3v rear-mounted cooling duct by cperiod

...wheel mount. that wheel leads to a somewhat convoluted internal shape, but it seems to work out okay. a...

thingiverse

free

ADKS Ender 3 Fan Duct v3 - Improved Mount by BlueHawke

...easier for cura to add tree supports to the internal volume. designed for a 4020 size parts cooling fan...

thingiverse

free

Emaker Huxley extruder drive with marker holders by Weldingrod1

...drive. it incorporates two marker holders, shorter filament overhang internaly, and clearance for a larger bowden tube fitting, and...

thingiverse

free

Prusa i3 X-Axis endstop bracket by RGN01

...ution-noncommercial-sharealike 4.0 international license. see http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.

thingiverse

free

Lewihe Play belt grip for X carriage AKA 'Bad boy' by magonegro

...having problems inserting the wires i have enhanced/widened the internal wormhole. now wire inserting is a breeze... update (10-may-2016):...

thingiverse

free

Modular Prusa X-carriage & e3D Chimera mount (layers fans, bed levelling, cable chain) by RGN01

...ution-noncommercial-sharealike 4.0 international license. see http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.

thingiverse

free

Ender 6 additions ventring, cablepipe holders and coolerfansupport by Lazybee

...frame. 20-march-2021 changed the framepart a little, made it internal wider from 15.5 to 16mm the cooler fan support...

thingiverse

free

Makita RT0700 Mount for X-Carve by shreddedbacon

...be using my shapeok2 carriage plate, and modified the internal diameter to fit the makita 65mm spindle. the plan...

thingiverse

free

XYZ da Vinci 1.0 E3D V6 Bowden complete conversion (no drilling, no cutting) (updated 3/8/17) by AndrewT111

...high infill percentage. a sparse infill can lead to internal wall buckling that'll make the part fail. i printed...

thingiverse

free

Ron's Compact Extruder by raldrich

...a long series of different extruder designs. i tried internal (ring) gears, a printed planetary gearbox, and a legoâ„¢...

thingiverse

free

Lewihe Play 3D LASER cutter/engraver mount by magonegro

...counter on screen without any hardware, just using marlin's internal extruder steps. once installed the adapter (yes! the pink...

thingiverse

free

Prusa i3 Steel upgrade X-carriage by RGN01

...ution-noncommercial-sharealike 4.0 international license. see http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.

thingiverse

free

Blower Fan Duct for Dual Extruder Cooling for Flashforge Inventor 3D Printer

...external supports. the design helps the printing of the internal bridges for smoother duct...

thingiverse

free

E3D Cyclops/Chimera Voron Afterburner toolhead by falcon14141

...understanding, the newer cyclops+ and chimera+ have a different internal layout, with more space in between the heatbreaks. i...

thingiverse

free

Mini Detachable Cooling Duct by BoothyBoothy

...for specific types of part where there may be internal walls (inside of a nut thread for example) which...

thingiverse

free

New CR-10s Filament Sensor Housing Assembly by DavidAELevy

...new sensor housing from scratch to use the same internal sensor switch pcb and m3 screws. my design firmly...

thingiverse

free

Anycubic i3 Mega CNC Router Conversion

...route your power and usb cables. removed all the internal wires that were not necessary for the operation of...

thingiverse

free

Prusa i3 steel 10mm upgrade by RGN01

...ution-noncommercial-sharealike 4.0 international license. see http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.

thingiverse

free

Chimera Nimble drive shaft spacer and cable retainer by RGN01

...ution-noncommercial-sharealike 4.0 international license. see http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.

thingiverse

free

Mar's E3D Trinity Mount: for mounting 3xE3Dv6's! (1.75mm and 3mm) by mar363636

...(lower fan) 8x m3 nuts 1x 30x30mm fan ( internal - recommended 1x 50x50mm fan (top) -required recommended printer...

thingiverse

free

Anet A3S Vortex Ring Fan Duct by OutcastZeroOne

...possible. march 30, 2018: i've reworked some of the internal cavity to allow for better airflow and reworked the...

thingiverse

free

X Axis Motor Mount and Idler - Angular Style by MattKi

...variations on the design if someone particularly wants an internal x idler (for...

thingiverse

free

8020 clip profiles for snap mount in 8020 and similar extrusions by the_digital_dentist

...clips that fit both profiles and found that the internal dimensions of the central slots is a little different...

thingiverse

free

Corexy plasma cutter by Stoney

...vertical dimensions are integers of 0.3mm. these are not internaly flanged to retain bearing and the inner hole is...

thingiverse

free

Backpack Part Cooler for FT-5 by CreativeSpark

...sturdy even in pla. the airflow has been directed internaly by turning vanes in order to achieve a relatively...

thingiverse

free

BareBone Fan System by PaperMakeiT

...the front! in other words, the cone need an internal cone to avoid this to happen. moreover you need...

thingiverse

free

Tronxy X5S Redesign

...for the angles do their job properly if the internal one is tightened with a nut (which has a...

thingiverse

free

MendelMax 2.0 RepRap Printable version V2! by JEZZMUND

...glue depending on your printer accuracy) also a 22mm internal diameter clamp that i'm using for my round (standard)...

thingiverse

free

Prusa Mini Detachable Cooling Duct Assembly by BoothyBoothy

...for specific types of part where there may be internal walls (inside of a nut thread for example) which...

thingiverse

free

DyzEnd Pro Mount for Ender 5 (Bowden setup) by lysithea81

...ar extreme high temperature plastic. that said, i've very briefly taken my dyzend to 450c in this nylon mount with no issues.

thingiverse

free

Kossel Mini Magnetic Ball Joint End Effector Upgrade V2 by Chimes_Industries

...the end effector is somewhat larger due to the internal ducting for the 30mm part cooling fan and location...

thingiverse

free

dual belt driven bed by ThijsOudeVrielink

...belt 150mm closed loop belt 5 pulleys with 8mm internal diameter (or whatever diameter rod you have lying around,...

thingiverse

free

Anet A6 Auto Bed Level Probe and Fan Mount Upgrade by Area51

...pin on the arduino must be set to have internal pull-up resistor activated to read the signal from the...

thingiverse

free

HOTAS Slide Throttle - Arduino Pro Micro, 12 buttons. by Omega489

...switches without adding diodes as the promicro has an internal pullup resistor. use a multistrand core wire for the...

thingiverse

free

Reworked OB1.4 open beam printer by Lucan07

...500mm height if possible. the printer is fairly large internal frame dimensions are 360x500 external dimensions with protrusions about...

thingiverse

free

CORE A8. (Anet A8 Core XY Conversion). by IIZEROXII

...2 x w8 length = 436mm there are some internal corner brackets if you prefer to use em made...

thingiverse

free

E3D_Cargo B140947 Modular Accessory Carriage by Eltron247

...also work here. this includes ducts that mount both internaly and externally. the external mounts will need to be...

thingiverse

free

Drag Knife Tool Holder (Remix - Scalable Pen Plotter)

...signer is planning on creating a vinyl cutting add on themselves sometime in the future. (please do correct me if i'm wrong).

thingiverse

free

E3D V6 3 Fan Shroud by Old-Steve

...340312 and 1973156 and remixed them. i liked the internal shape of 340312 for heat sink air flow, and...