30 coat revised 3d models found
Download or buy, then render or print from the shops or marketplaces.
3D Models below are suitable not only for printing but also for any
computer graphics like CG, VFX, Animation, or even CAD. You can print these 3d models on
your favorite 3d printer or render them with your preferred render engine.
Please note that the 3D model database is only a Search Engine. You should
visit the original websites. Most of the models can be easily imported and rendered
with Autodesk 3ds Max, Maya, Blender, C4D, and Sketchup. Check for online
3d model conversions tools for your file format.
thingiverse
free
Herman Miller office cubical coat hanger snap in by hxtasy
...cer, otherwise the coat will tend to get caught on the square edge and not come off as easily.
should fit other model office also
thingiverse
free
NeverTouch by crimson_phoenix
...porous and therefore should be treated with a top coat to prevent germs from going into the pores of...
thingiverse
free
Hudson Tipper railway truck. (new hubs) by dagnall53
...i used 3mm rod for the axle.(from a wire coat hanger suitably straightened). the height of wheel etc with...
thingiverse
free
Cubicle Coat Hook (remix) by akajester
...the edges have been rounded, cut out some filament in the middle and it's wider so it fits tighter and slips off less. enjoy!
thingiverse
free
Elsa Frozen Coat hook by harddrv1
...on added another version that does not have my daughters name on it for those of you that do not have a daughter named madison :)
thingiverse
free
MK7 Extruder Drive by fittoextrude
...smear it on the filament. this will season and coat the steel inside your heat break and create a...
thingiverse
free
iPad Support and Adjustable Stand by MauiMacMan
...for mom with clumsy fingers, it works great. i coatd the bottom of the base with liquid rubber (dipit)...
thingiverse
free
Gladiator GearTrack Shoe Rack Helmet Hook by j0dan
...cut the screws to fit. they are very common coat hooks, but you will likely want to grab the...
thingiverse
free
Surface mount for TechMatte magnetic phone mount by schleppy
...perfectly, even with a coat of primer and two coat of paint on it. i also designed this piece...
thingiverse
free
Bathook - coat hook for a cubicle by kmrohr
...d a second hook that is a little wider and has some extra support in the lower hook area. still works with the same batman logo.
thingiverse
free
FrSky Taranis Thumb Stick Pads by aimhelix
...is. after the print, i also recommend in 2-3 coat of plastidip for smoothness, texture and...
thingiverse
free
N Scale Lighted Dwarf Signals by ajkochev
...the following: materials: various leds smd 603 size enamel coatd magnet wire 38 to 42 awg (you will need...
thingiverse
free
Comlink from Star Wars Rebels by mooslug
...some). the "grip" section should be painted black or coatd in black plasti-dip. the "mic" and "cap" should be...
thingiverse
free
Hanger Hanger for Ivar shelving by ottaross
...the shelf (e.g. your iron). you can hang a coat on it. you can hang your keys on it....
thingiverse
free
Spring Razor from Dishonored by pksystems
...lighter to the wire, and stripped off the plastic coatng. ...
thingiverse
free
Chain mail tri-mesh improved by dfyler
...petg with a bed covered in blue tape and coatd with diluted white glue. keep an eye on the...
thingiverse
free
lead screw motor mount revised stronger by locutus40
...not the cheap kind thin so it flows and coat the layers this seals it if you use pla...
thingiverse
free
Air Compressor Tire Inflator with gauge by willfly
...water. it may be sealed with a brush on coat of polyurethane or runny epoxy. i didn't bother with...
thingiverse
free
Realacc X210 V+ "The Piggy" winter canopy pod by mukha521
...of shortenings in parts like usb connector that isn't coatd. well, i decided to make a canopy that will...
thingiverse
free
Savi's Workshop / Galaxy's Edge Lightsaber Blade Insert
...a bit of sandpaper first to remove any non-conductive coatng and file down one edge if it overhangs the...
thingiverse
free
225mm Freestyle Quad **Revised 10_19_20 by ScrapHeapInd
...the normal stuff. i also used the water proof coatng on all boards. cool with a black light. anyway,...
thingiverse
free
Better Cooler Drain Plug (RubberMaid Cooler) with o-rings. by DrPeper
...of abs. it fits like a dream. first i coatd the o-rings with the proper silicone grease. it only...
thingiverse
free
SimpleDraw by cassiofiorin
...profiles at a good price, as well as the coatd bearings. for the drive i choose to use second-hand...
thingiverse
free
![[Fixed] Dual 26650 vape with linear magnetic switch (print in place) by Alex_Thunder](/t/8611381.jpg)
[Fixed] Dual 26650 vape with linear magnetic switch (print in place) by Alex_Thunder
...the box and button you can paint or resin coat i used an epoxy resin product called xtc-3d combined...
thingiverse
free
Low Bypass Turbofan Jet Engine by gahwar
...parts have been painted with glossy black as base coat and finished with lacquer metalizer. all the printed parts...
thingiverse
free
Zortrax M200 dual airflow radial fan duct by liftbag
...you must isolate the hotend, for example with cotton coat that can be found on the market or you...
thingiverse
free
Carbon Fibre Tube Quadcopter - Kraken Pod by MantleQuads
...up a little bit of epoxy and applying it.) coat the edges of the exposed notch on each tube...
thingiverse
free
Da Vinci Duo 2.0 Chimera Edition with 200x200 printbed upgrade by NAK3DDesigns
...your two print heads as per e3d v6 instructions. coat the slides with heat gel and insert into the...
thingiverse
free
EC-RE011 Campagnolo 8 Speed Ergo right shifter Spring Carrier by elhalpern
...still pivot freely. i installed the steel printed carrier (coatd in grease to lessen corrosion) with new g-springs, and...
thingiverse
free
Lure of the Prophets (a boardgame) W.I.P. by Massenzio
...need to refine the factions knights (but crest , coatof-arms and shields are easy , or at least, appear...